DUST COLLECTOR ACCESSORY KIT
Model 47911
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
7.
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etcetera.
8.
9.
INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENT.
STAY ALERT. Watch what you are doing at all times. Use common sense. Do
not use this product when you are tired or distracted from the job at hand.
10.
11.
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that
it will operate properly and perform its intended function. Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace or repair damaged or worn parts immediately.
REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only
identical replacement parts. Only use accessories intended for use with this
product. Approved accessories are available from Harbor Freight Tools.
12.
13.
14.
MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean and dry for
better and safer performance.
MAINTENANCE: For your safety, service and maintenance should be performed
regularly by a qualified technician.
USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool,
attachment, or accessory to do the work of a larger industrial tool, attachment, or
accessory. There are certain applications for which this product was designed. It
will do the job better and more safely at the rate for which it was intended. Do
not modify this attachment, and do not use this product for a purpose for which it
was not intended.
15.
WARNING: The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur. The operator
must understand that common sense and caution are factors, which cannot be
built into this product, but must be supplied by the operator.
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS
1.
2.
MAINTAIN A SAFE WORKING ENVIRONMENT. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Always keep the work
area free of obstructions, grease, oil, trash, and other debris.
MAKE SURE TO READ AND UNDERSTAND ALL INSTRUCTIONS, AND
SAFETY PRECAUTIONS, AS OUTLINED IN THE MANUFACTURER’S
MANUAL OF THE POWER EQUIPMENT TO WHICH THE DUST COLLECTOR
ACCESSORY KIT WILL BE ATTACHED.
SKU 47911
PAGE 3
3.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are: lead from lead-based paints, crystalline silica from bricks
and cement or other masonry products, arsenic and chromium from chemically
treated lumber. Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these chemicals: work in a
well ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles. (Cali-
fornia Health & Safety Code 25249.5, et seq.)
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 6 are
included. If any parts are missing or broken, please call Harbor Freight Tools at the num-
ber shown on the cover of this manual as soon as possible.
PRODUCT OVERVIEW
1.
The Dust Collector Accessory Kit is designed for one and two power equipment
tool hook-ups, and is typically used for the collection of wood dust, wood chips,
sand, and other light debris. The Dust Collector Accessory Kit may be attached
to table saws, band saws, sanders, router tables, shapers, jointers, and variety of
dust collecting machines all having a 4” dust port. Due to the wide diversity of
power machinery to which the Dust Collector Kit may be attached, it is recom-
mended that only a qualified technician perform the assembly procedure.
ASSEMBLY INSTRUCTIONS
NOTE: For additional references to the parts listed below, refer to the
AssemblyDiagram on page 6.
1.
Though the Dust Collector Accessory Kit is designed to offer a wide variety of appli-
cations, the following illustration depicts a typical assembly method to hook-up one power
equipment tool and two power equipment tools. (See Figure A, next page.)
2.
NOTE: The Dust Collector Accessory Kit is designed to be attached to stationary
power equipment tools and dust collectors having 4” diameter dust ports. De-
pending on the diameter of the dust port of your power equipment tools and dust
collector, it may be necessary to attach size adapters (not provided) to ensure a
proper fit.
SKU 47911
PAGE 4
DUST HOOD (#3)
OR
TABLE SAW DUST HOOD (#5)
BLAST GATE (#2)
STEEL CLAMP (#6)
POWER
DUST
TOOL
PORT
DUST
PORT
FLEXIBLE HOSE (#1)
DUST
COLLECTOR
“Y” FITTING
TO ATTACH TO
ONE OR TWO
POWER TOOLS
FIGURE A
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
CAUTION: Prior to performing any inspection, maintenance, or cleaning on the
Dust Collector Accessory Kit, make sure to disconnect the machine(s) to which
the Accessory Kit is attached from its electrical power outlet.
BEFORE EACH USE, inspect the general condition of the Dust Collector Acces-
sory Kit. Check for loose connections, misalignment or binding of moving parts,
cracked, torn, or broken parts, and any other condition that may affect its safe
operation. If abnormal noise or vibration occurs, have the problem corrected
before further use. Do not use damaged equipment.
3.
DAILY: With a soft brush, cloth, or vacuum, remove all debris from the Dust
Collector Accessory Kit. If necessary, you may use a mild detergent.
SKU 47911
PAGE 5
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTUER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
ꢋꢌꢆꢁꢍꢎ
ꢃꢂꢄꢅꢆꢇꢈꢁꢇꢉꢊ
ꢛ0ꢌꢚꢈꢏ ꢔꢄꢔꢅꢌꢕꢌꢜ!.ꢌ'ꢁꢂꢑꢌꢐꢎꢔꢕꢈꢖꢎꢔꢌꢗꢁꢃꢔ
ꢛ0ꢌꢚꢈꢏ ꢔꢄꢔꢅꢌꢊꢎꢏꢃꢄꢌ+ꢏꢄꢔ
/0ꢌꢚꢆꢃꢄꢌꢗꢁꢁ&
/<0ꢌꢐꢈꢄꢄꢈꢂꢑ
ꢜ*0ꢌ>ꢏꢖꢎꢔꢌꢋꢏꢞꢌꢚꢆꢃꢄꢌꢗꢁꢁ&
ꢛ0ꢌꢚꢁꢆꢖꢎꢔꢌꢘꢈꢅꢔꢌꢋꢄꢔꢔꢎꢌꢀꢎꢏ ꢙꢃ
ꢏꢁꢐꢑ
*
*
ꢜ
ꢜ
ꢜ
ꢜ!
ꢜ
*
$
ꢛ
=
/
ASSEMBLY DIAGRAM
1
6
2
5
3
4
SKU 47911
PAGE 6
|