®
ELECTRIC
COMBINATION
LOWER OVEN
Use & Care Guide
In the U.S.A., for questions about features, operation, performance,
parts, accessories or service, call: 1-800-253-1301.
or visit our website at...
Table of Contents............................................ 2
MODELS GMC275 RMC275
GMC305 RMC305
8300610
OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical
shock, injury to persons, or damage when using the
oven, follow basic precautions, including the following:
■ Use Care When Opening Door – Let hot air or steam
escape before removing or replacing food.
■ Do Not Heat Unopened Food Containers – Build-up
of pressure may cause container to burst and result
in injury.
■ Proper Installation – Be sure the oven is properly
installed and grounded by a qualified technician.
■ Keep Oven Vent Ducts Unobstructed.
■ Never Use the Oven for Warming or Heating the
Room.
■ Placement of Oven Racks – Always place oven racks
in desired location while oven is cool. If rack must be
moved while oven is hot, do not let potholder contact
hot heating element in oven.
■ Do Not Leave Children Alone – Children should not
be left alone or unattended in area where oven is in
use. They should never be allowed to sit or stand
on any part of the oven.
■ Wear Proper Apparel – Loose-fitting or hanging
garments should never be worn while using the oven.
■ User Servicing – Do not repair or replace any part of
the oven unless specifically recommended in the
manual. All other servicing should be referred to a
qualified technician.
■ Storage in Oven – Flammable materials should not
be stored in an oven.
■ DO NOT TOUCH HEATING ELEMENTS OR
INTERIOR SURFACES OF OVEN – Heating
elements may be hot even though they are dark in
color. Interior surfaces of an oven become hot
enough to cause burns. During and after use, do
not touch, or let clothing or other flammable materials
contact heating elements or interior surfaces of oven
until they have had sufficient time to cool. Other
surfaces of the oven may become hot enough to
cause burns – among these surfaces are oven vent
openings and surfaces near these openings, oven
doors, and windows of oven doors.
■ Do Not Use Water on Grease Fires – Smother fire or
flame or use dry chemical or foam-type extinguisher.
■ Use Only Dry Potholders – Moist or damp potholders
on hot surfaces may result in burns from steam. Do
not let potholder touch hot heating elements. Do not
use a towel or other bulky cloth.
SAVE THESE INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
For self-cleaning ovens:
■ Clean Only Parts Listed in Manual.
■ Do Not Clean Door Gasket – The door gasket is
essential for a good seal. Care should be taken not
to rub, damage, or move the gasket.
■ Before Self-Cleaning the Oven – Remove broiler pan
and other utensils.
■ Do Not Use Oven Cleaners – No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
SAVE THESE INSTRUCTIONS
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list
of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and
requires businesses to warn of potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or
other reproductive harm.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde,
carbon monoxide, and toluene.
4
PARTS AND FEATURES
This manual covers different models. The oven you have purchased may have some or all of the items listed. The locations and
appearances of the features shown here may not match your model. On I-enabled products, please consult the Use and Care Guide
and Installation Guide that have been provided with the Web Tablet and Integrated Home Management System.
6
1
2
3
7
8
4
9
5
1. Upper Oven
6. Electronic Oven Control
7. Automatic Oven Light Switch
8. Oven Lock Latch
Parts and Features not shown
Oven Lights
(see separate Use and Care Guide)
2. Oven Vent
3. Broil Element (not shown)
4. Bake Element
Broiler Pan and Grid
Roasting Rack
9. Model and Serial Number Plate
(on right mounting rail)
5. Oven Door Window
5
ELECTRONIC OVEN CONTROL
1
2
3
4
5
LOWER OVEN
1
4
7
2
5
8
3
6
9
C
F
CUSTOM
BROIL
MICROWAVE OVEN
TEMP
BAKE
HEAT CONVECT
DELAY BAKE
TIMED BROIL
TIMER
STOP
ON
START ?
AUTO
DOOR LOCKED CLEAN
MICRO
REHEAT DEFROST
COOK
TIME
CLEAN
TIME
ADD
MINUTE
COOK
POWER
0
AUTO
BROIL
START
ENTER
TIMER
OFF
TIMER
SET
CRISP
QUANTITY
COOK
DELAY
START
TIME
COOK
TIME
STOP
TIME
HR
MIN
OFF
CANCEL
START
ENTER
COOK A
BIT MORE
OFF
CANCEL
WARM
MEMORY
HOLD
POPCORN
(3 SIZES)
CLOCK LIGHT
6
7
8
9
10
11 12
1. Oven Setting Pads
2. Temperature Pad
3. Timer Set and Off
4. Electronic Display
5. Microwave Oven Controls 9. Clock Pad
6. Electronic Clock Control
10. Light Pad
11. Off/Cancel Pad
12. Start/Enter Pad
Pad
7. Hour Pad
8. Minute Pad
Display
Clock
When power is first supplied to the appliance, “PF” will appear on
the display. Press OFF/CANCEL to clear.
This is a 12 hour clock and does not show a.m. or p.m.
To Set:
Any other time “PF” appears, a power failure has occurred. Press
OFF/CANCEL and reset the Clock if needed.
Before setting, make sure the oven, Timer and Timed Cooking
are off.
When the oven is in use, the display shows preheat time and the
temperature and oven setting.
1. Press CLOCK.
2. Press the HR or MIN “up” or “down” arrow pads to set the
When the oven is not in use, the display shows the time of day.
time of day.
When using COOK TIME (on some models), the display will show
either hours and minutes, or minutes and seconds.
3. Press CLOCK or START/ENTER.
To Disable:
Start/Enter
The clock time can be disabled so that it does not show on the
display. To disable, press and hold CLOCK for 5 seconds. To
display the clock time again, press and hold CLOCK for 5
seconds and the time of day will show on the display. The clock
time should not have to be reset.
The START/ENTER pad begins any oven function except the
Timer. If not pressed within 5 seconds after pressing a function
pad, the “START?” indicator light will flash as a reminder. On
some models, “START?” will appear on the display.
If not pressed within 4 to 5 minutes (depending on your model)
after pressing a function pad, the oven display will return to the
time of day mode and the programmed function will be
cancelled.
Tones
Tones are audible signals, indicating the following:
One tone
Off/Cancel
■
■
■
Valid pad press
The OFF pad stops any function except the Clock, Timer and
Control Lock.
Oven is preheated
Function has been entered
Three tones
■
Invalid pad press
Four tones
■
End-of-cycle
■
Reminder, repeating each minute after the end-of-cycle tones
6
All Tones
All of the above tones are preset on, all except the end-of-cycle
tones can be turned off.
Control Lock
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven.
To Turn Off/On: Press and hold STOP TIME for 5 seconds. A
tone will sound and “oFF” or “Snd OFF” (depending on your
model) will appear on the display. Repeat to change back to “on”
or “Snd On” (depending on your model).
When the control is locked, only the CLOCK and TIMER pads will
function.
To Lock/Unlock Control: Before locking, make sure the oven
and Timer are off. Press and hold START/ENTER for 5 seconds. A
single tone will sound and “LOC” will appear on the display.
“LOC” will also appear whenever any command pad is pressed
while the control is locked. Repeat to unlock, and “LOC” will
disappear from the display.
Reminder Tones
Reminder tones are four 1-second tones which indicate that the
set time has expired for a timer or a timed oven control function.
To Turn Off/On: Press and hold COOK TIME for 5 sec. On some
models, “NAG OFF” or “NAG ON” will appear on the display.
Tone Volume
Oven Temperature Control
The volume is preset at high, but can be changed to low.
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door and element or
burner cycling may give incorrect readings.
To Change: Press and hold DELAY START for 5 seconds. A tone
will sound and “HI” or “Snd HI” (depending on your model) will
appear on the display. Repeat to change back to “LO” or “Snd
LO” (depending on your model).
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
Fahrenheit and Celsius
A minus sign means the oven will be cooler by the displayed
amount. No sign means the oven will be warmer by the displayed
amount. Use the following chart as a guide.
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
To Change: Press and hold CUSTOM BROIL for 5 seconds. A
tone will sound and “C” will appear on the display. Repeat to
change back to Fahrenheit. To remove, press UPPER OFF,
LOWER OFF or OFF/CANCEL.
ADJUSTMENT °F
(ADJUSTMENT °C)
COOKS FOOD
10°F (5°C)
...a little more
...moderately more
...much more
Timer
20°F (10°C)
30°F (15°C)
-10°F (-5°C)
-20°F (-10°C)
-30°F (-15°C)
The Timer can be set in hours or minutes up to 12 hours and 59
minutes and counts down the set time. The Timer does not start
or stop the oven.
...a little less
To Set:
1. Press TIMER SET.
...moderately less
...much less
If no action is taken after 1 to 4 minutes (depending on your
model), the display will return to the time of day mode.
2. Press the HR or MIN “up” or “down” arrow pads to set the
length of time.
To Adjust Oven Temperature Calibration:
3. Press TIMER SET or START/ENTER.
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “00.”
If not pressed within a certain amount of time, the display will
return to the time of day mode and the programmed function
will be cancelled.
2. Press the TEMP “up” or “down” arrow pad(s) to increase or to
decrease the temperature in 10°F (5°C) amounts. The
adjustment can be set between 30°F (15°C) and -30°F
(-15°C).
When the set time ends, end-of-cycle tones will sound, then,
if on, reminder tones will sound every minute.
3. Press START/ENTER.
4. Press TIMER OFF anytime to cancel the Timer and/or stop
reminder tones.
Remember, do not press the OFF/CANCEL pad because the
oven will turn off.
The time can be reset during the countdown by repeating the
above steps.
To display the time of day when the timer is counting down, press
CLOCK.
7
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow 2 in.
(5 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
BEFORE USING
Odors are normal when the range is new. This happens the first
time the oven is used.
NUMBEROF POSITION ON RACK
PAN(S)
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well
ventilated room.
1
Center of rack.
2
Side by side or slightly staggered.
3 or 4
Opposite corners on each rack. Make sure
that no bakeware piece is directly over
another.
Aluminum Foil
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
■
Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
Bakeware
The bakeware material affects cooking results. Follow
■
To catch spills, place foil on rack below dish. Make sure foil is
at least 1 in. (2.5 cm) larger than the dish and that it is turned
up at the edges.
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
BAKEWARE/
RESULTS
RECOMMENDATIONS
■
Do not cover food with aluminum foil when convection
cooking (on some models).
Light colored
aluminum
■
Use temperature and time
recommended in recipe.
Positioning Racks and Bakeware
■
Light golden
crusts
IMPORTANT: Never place food or bakeware directly on the oven
door or bottom. Permanent damage will occur to the porcelain
finish.
■
Even browning
RACKS
Dark aluminum
and other
bakeware with
dark, dull and/or
non-stick finish
■
May need to reduce baking
temperatures 25°F (15°C).
Position racks before turning the oven on. Do not move racks
with bakeware on them. Make sure racks are level. To move a
rack, pull it out to the stop position, raise the front edge, then lift
out. Use the following illustration and chart as a guide.
■
■
Use suggested baking time.
For pies, breads and casseroles, use
temperature recommended in
recipe.
■
Brown, crisp
crusts
■
Place rack in center of oven.
Insulated cookie
sheets or baking
pans
■
■
Place in the bottom third of oven.
May need to increase baking time.
■
Little or no
bottom
browning
Stainless steel
■
May need to increase baking time.
FOOD
RACK POSITION
■
Light, golden
crusts
Frozen pies, large roasts, turkeys,
angel food cakes
1 or 2
■
Uneven
browning
Bundt cakes, most quick breads,
yeast breads, casseroles, meats
2
Stoneware
■
■
Follow manufacturer’s instructions.
■
Crisp crusts
Cookies, biscuits, muffins, cakes,
non-frozen pies
2 or 3
Ovenproof
glassware,
ceramic glass or
ceramic
May need to reduce baking
temperatures 25°F (15°C).
■
Brown, crisp
crusts
8
Meat Thermometer
OVEN USE
On models without a temperature probe, always rely on a meat
thermometer to determine doneness of meat and poultry. The
internal temperature, not appearance, is what counts. A meat
thermometer is not supplied with this appliance.
Baking and Roasting
ACCUBAKE® Temperature Management System
■
■
■
Insert the thermometer into the center of the thickest portion
of the meat or inner thigh or breast of poultry. The tip of the
thermometer should not touch fat, bone or gristle.
(on some models)
The ACCUBAKE system electronically regulates the oven heat
levels during preheat and bake to maintain a precise temperature
range for optimal cooking results. The bake and broil elements
cycle on and off in intervals. The bake element will glow red when
cycling on, the broil element will not. This feature is automatically
activated when the oven is in use.
After reading the thermometer once, push it into the meat
¹⁄₂ in. (1.25 cm) more and read again. If the temperature
drops, cook the meat or poultry longer.
Check all meat in two or three places.
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat conditioning time to
end before putting food in unless recommended in the recipe.
Oven Vent
1
2
3
To Bake or Roast:
1. Press BAKE.
Press TEMP (▲) or (▼) to set a temperature other than 350°F
(175°C) in 5° amounts. The bake range can be set between
170°F and 500°F (75°C and 260°C).
1. Upper oven
2. Oven vent
3. Lower oven
2. Press START.
The temperature can be changed after this step.
START does not need to be pressed again.
The oven vent should not be blocked or covered since it allows
the release of hot air and moisture from the oven. Doing so will
cause poor air circulation, affecting cooking and cleaning results.
Never set plastics, paper or other items that could melt or burn
near the oven vent.
3.
Press OFF when finished.
Preheating
After START is pressed, the oven will enter a timed preheat
conditioning. “PrE” and the time countdown will appear on the
display. When the preheat conditioning time ends, a tone will
sound and the selected temperature will appear on the display.
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ.
Waiting an additional ten minutes after the preheat conditioning
time ends to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
9
BROILING CHART
For best results, place food 3 in. (7 cm) or more from the broil
burner. Times are guidelines only and may need to be adjusted
for individual tastes. Recommended rack positions are numbered
from the bottom (1) to the top (5). For diagram, see the
“Positioning Racks and Bakeware” section.
Broil
Broiling uses direct radiant heat to cook food. Changing the
temperature when Custom Broiling allows more precise control
when cooking. The lower the temperature, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, fish
and poultry may cook better at lower broiling temperatures.
Approximate
RACK
POSITION
Time (minutes)
■
Use only the broiler pan and grid provided with the range. It is
designed to drain juices and help prevent spatter and smoke.
FOOD
SIDE 1
SIDE 2
■
For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
Steak
1 in. (2.5 cm) thick
medium rare
medium
4
4
4
14-15
15-16
18-19
7-8
■
■
Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to prevent curling.
8-9
well done
9-10
Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
*Ground meat patties
³⁄₄ in. (2 cm) thick
well done
4
4
13-14
21-22
6-7
■
After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
Pork chops
1 in. (2.5 cm) thick
10-11
Before broiling, position rack according to Broiling chart. It is not
necessary to preheat the oven before putting food in unless
recommended in the recipe. Position food on grid in the broiler
pan, then place it in the center of the oven rack. Close the door.
Ham slice, precooked
¹|₂ in. (1.25 cm) thick
4
4
8-10
6-7
4-5
3-4
Frankfurters
To Broil:
1. Press CUSTOM BROIL.
2. Press START/ENTER.
3. Press OFF/CANCEL when finished.
To Custom Broil:
Lamb chops
1 in. (2.5 cm) thick
4
15-17
8-9
Chicken
bone-in pieces
boneless breasts
3
4
18-20
12-16
18-20
11-16
1. Press CUSTOM BROIL.
2. Press TEMP “up” or “down” arrow pad to change the
temperature in 5° amounts. The broil range can be set
between 170°F (75°C) and HI (500°F [260°C]).
Fish
Fillets ¹|₄- ¹|₂ in.
(.6-1.25 cm) thick
Steaks ³|₄- 1 in.
(2-2.5 cm) thick
4
4
8-10
4-5
7-9
3. Press START/ENTER.
4. Press OFF/CANCEL when finished.
15-18
* Place up to 9 patties, equally spaced, on broiler grid.
10
To Set a DELAY START TIME:
1. Press BAKE.
Timed Cooking
Press TEMP “up” or “down” arrow pad to set a temperature
other than 350°F (175°C) in 5° amounts. The bake range can
be set between 170°F and 500°F (75°C and 260°C).
WARNING
2. Press DELAY START TIME.
Food Poisoning Hazard
3. Press HR and MIN “up” or “down” arrow pad until the desired
time of day to start appears on the display.
Do not let food sit in oven more than one hour
before or after cooking.
4. Press START/ENTER.
The temperature can be changed after this step. START/
ENTER does not need to be pressed again.
Doing so can result in food poisoning or
sickness.
When the delay start time is reached, a tone will sound. The
display will count down the set cook time.
Timed Cooking allows the oven to be set to turn on at a certain
time of day, cook for a set length of time, and/or shut off
automatically. DELAY START TIME should not be used for food
such as breads and cakes because they may not bake properly.
5. Press OFF/CANCEL when finished.
To Set a COOK TIME and DELAY START TIME:
1. Press BAKE.
Before setting, make sure the clock is set to the correct time of
day. See “Clock” section.
Press TEMP “up” or “down” arrow pad to set a temperature
other than 350°F (175°C) in 5° amounts. The bake range can
be set between 170°F and 500°F (75°C and 260°C).
To Set a COOK TIME:
1. Press BAKE.
2. Press COOK TIME.
Press TEMP “up” or “down” arrow pad to set a temperature
other than 350°F (175°C) in 5° amounts. The bake range can
be set between 170°F and 500°F (80°C and 260°C).
3. Press HR and MIN “up” or “down” arrow pad until the desired
length of time appears on the display.
4. Press DELAY START TIME.
2. Press COOK TIME.
5. Press HR and MIN “up” or “down” arrow pad until the desired
3. Press HR and MIN “up” or “down” arrow pad until the desired
time of day to start appears on the display.
length of time appears on the display.
6. Press START/ENTER.
4. Press START/ENTER.
The temperature and set cook time can be changed after this
step. START/ENTER does not need to be pressed again.
The temperature and set cook time can be changed after this
step. START/ENTER does not need to be pressed again.
When the delay start time is reached, a tone will sound. The
display will count down the set cook time.
When the set cook time ends, the oven will shut off
automatically and “End” will appear on the display. End-of-
cycle tones will sound, then reminder tones will sound every
minute until OFF/CANCEL is pressed.
When the set cook time ends, the oven will shut off
automatically and “End” will appear on the display. End-of-
cycle tones will sound, then reminder tones will sound every
minute until OFF/CANCEL is pressed.
5. Press OFF/CANCEL anytime to end Timed Cooking or to
stop reminder tones and clear the display.
7. Press OFF/CANCEL anytime to end Timed Cooking or to
stop reminder tones and clear the display.
11
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
OVEN CARE
The Self-Cleaning cycle uses very high temperatures, burning soil
to a powdery ash.
Self-Cleaning Cycle
The oven is preset for a 3 hour 30 minute clean cycle, but the
time can be changed. Suggested clean times are 2 hours 30
minutes for light soil and between 3 hours 30 minutes to 4 hours
30 minutes for average to heavy soil.
(on some models)
WARNING
Once the oven has completely cooled, remove ash with a damp
cloth. Do not wipe down any of the inside surfaces until the oven
has completely cooled down. Applying a cool damp cloth to the
inner door glass before it has completely cooled could result in
the glass breaking.
The oven light will not work during the Self-Cleaning cycle.
To Self-Clean:
Before self-cleaning, make sure the door is closed completely or
it will not lock and the cycle will not begin.
Burn Hazard
1. Press AUTO CLEAN.
Do not touch the oven during the
Self-Cleaning cycle.
2. Press the HR and MIN “up” or “down” arrow pad to set a
clean time other than 3 hour 30 minutes. The clean time can
be set between 2 hours 30 minutes and 4 hours 30 minutes.
Keep children away from oven during
Self-Cleaning cycle.
3. Press START/ENTER.
The oven door will automatically lock. “LOCKED” will appear
on the display. The door will not unlock until the oven cools.
Failure to follow these instructions can result
in burns.
When the cycle is complete and the oven cools, “End” will
appear on the oven display and “LOCKED” will disappear.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well ventilated room.
4. Press OFF/CANCEL or open the oven door to clear the oven
display.
To Delay Start Self-Clean:
Self-clean the oven before it becomes heavily soiled. Heavy soil
results in longer cleaning and more smoke.
Before delay starting Self-Clean, make sure the clock is set to the
correct time of day. See “Clock” section. Also, make sure the
door is closed completely or it will not lock and the cycle will not
begin.
Keep the kitchen well-ventilated during the Self-Cleaning cycle to
help get rid of heat, odors, and smoke.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. See “Oven Vent(s)” section.
1. Press AUTO CLEAN.
Press the HR “up” or “down” arrow pad to set a clean time
other than 3 hour 30 minutes. The clean time can be set
between 2 hours 30 minutes and 4 hours 30 minutes.
Do not clean, rub, damage or move the oven door gasket. The
door gasket is essential for a good seal.
2. Press DELAY START TIME.
Prepare Oven:
3. Press the HR and MIN “up” or “down” arrows pads to enter
■
■
■
■
Remove the broiler pan, grid, cookware and bakeware and,
on some models, the temperature probe from the oven.
the time of day to start.
4. Press START/ENTER.
Remove any foil from the oven because it may burn or melt,
damaging the oven.
The start time is automatically calculated and displayed.
The door will automatically lock and “LOCKED” and “DELAY”
will appear on the display. The door will not unlock until the
oven cools.
Remove oven racks to keep them shiny and easy to slide.
See “General Cleaning” section for more information.
Hand clean inside door edge and the 1½ in. (3.8 cm) area
around the inside oven cavity frame, being careful not to
move or bend the gasket. This area does not get hot enough
during self-cleaning to remove soil. Do not let water, cleaner,
etc. enter slots on door frame. Use a damp cloth to clean this
area.
When the start time is reached, the oven will automatically
turn on.
When the cycle is complete and the oven cools, “End” will
appear on the lower oven display and “LOCKED” will
disappear.
■
Wipe out any loose soil to reduce smoke and avoid damage.
At high temperatures, foods react with porcelain. Staining,
etching, pitting or faint white spots can result. This will not
affect cooking performance.
5. Press any pad or open the oven door to clear the oven
display.
To Stop Self-Clean any time:
Press OFF/CANCEL. If the oven temperature is too high, “cln,”
“TIMED,” “ON,” “cool,” and “LOCKED” will appear on the display
and the door will remain locked. It will not unlock until the oven
cools.
12
BROILER PAN AND GRID
General Cleaning
Do not clean in the Self-Cleaning cycle.
IMPORTANT: Before cleaning, make sure all controls are off and
the oven is cool. Always follow label instructions on cleaning
products.
■
Mildly abrasive cleanser:
Scrub with wet scouring pad.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
■
Solution of ¹|₂ cup (125 mL) ammonia to 1 gallon (3.75 L)
water:
STAINLESS STEEL (on some models)
Soak for 20 minutes, then scrub with scouring or steel wool
pad.
Do not use soap-filled scouring pads, abrasive cleaners, Cooktop
Polishing Creme, steel-wool pads, gritty wash cloths or some
paper towels. Damage may occur.
■
Oven cleaner:
Follow product label instructions.
Rub in direction of grain to avoid damaging.
Porcelain enamel only, not chrome
Dishwasher
■
■
■
Stainless Steel Cleaner & Polish (not included):
See “Assistance or Service” section to order.
Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
Vinegar for hard water spots
■
Oven Lights
The oven lights are standard 40-watt appliance bulbs. They will
come on when the oven door is opened. They will not work
during the Self-Cleaning cycle. When the oven door is closed,
press OVEN LIGHT to turn them on or off.
OVEN DOOR EXTERIOR
To Replace:
■
Glass cleaner and paper towels or non-abrasive plastic
scrubbing pad:
Before replacing, make sure the oven is off and cool.
1. Disconnect power.
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
CONTROL PANEL
Do not use abrasive cleaners, steel-wool pads, gritty wash cloths
or some paper towels. Damage may occur.
■
Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb and bulb cover by turning clockwise.
5. Reconnect power.
OVEN CAVITY
Do not use oven cleaners.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
■
Self-Cleaning cycle:
See “Self-Cleaning Cycle” first.
OVEN AND ROASTING RACKS
■
Self-Cleaning cycle:
See “Self-Cleaning Cycle” first. Remove racks or they will
discolor and become harder to slide. If this happens, a light
coating of vegetable oil applied to the rack guides will help
them slide.
■
Steel wool pad
13
Oven Door
TROUBLESHOOTING
For normal range use, it is not suggested to remove the oven
door. However, if necessary, follow these instructions. The oven
door is heavy.
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
To Remove:
1. Open oven door all the way.
Nothing will operate
2. Flip up the hinge latch on each side.
■
■
Has a household fuse been blown or has the circuit
breaker been tripped?
Replace the fuse or reset the circuit.
Is the appliance wired properly?
See Installation Instructions.
Oven will not operate
■
■
■
■
■
Is the electronic oven control set correctly?
See “Electronic Oven Control” section.
Has a delay start been set?
See “Timed Cooking” section.
3. Close the oven door as far as it will shut.
On some models, is the Control Lock set?
See “Control Lock” section.
4. While holding the oven door on each side with both hands, lift
the oven door up.
On some models, is the Sabbath Mode set?
See “Sabbath Mode” section.
Continue to push the oven door closed and pull it away from
the oven door frame.
On double oven models, is one oven self-cleaning?
When one oven is self-cleaning the other oven cannot be set
or turned on.
■
On double oven models, has the correct oven been
selected?
Choose UPPER OVEN or LOWER OVEN first.
Oven temperature too high or too low
■
Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.
Display shows messages
■
■
Is the display showing “PF”, “PF id=27” or “PF id=30”?
There has been a power failure. Clear the display. See
“Display(s)” section. On some models, reset the clock, if
needed. See “Clock” section.
To Replace:
1. Insert both hanger arms into the door.
Is the display showing a letter followed by a number?
Clear the display. See “Display(s)” section. If it reappears, call
for service. See “Assistance or Service” section.
Self-Cleaning cycle will not operate
■
■
■
Is the oven door open?
Close the oven door all the way.
Has the function been entered?
See “Self-Cleaning Cycle” section.
On some models, has a delay start Self-Clean cycle been
set?
See “Self-Cleaning Cycle” section.
■
■
Has a delay start been set?
See “Timed Cooking” section.
On double oven models, is one oven self-cleaning?
When one oven is self-cleaning, the other oven cannot be set
to self-clean.
2. Open the oven door.
You should hear a “click” as the door is set into place.
3. Move the hinge levers back to the locked position. Ensure
that the door is free to open and close. If not, repeat the
removal and installation procedures.
14
Oven cooking results not what expected
ASSISTANCE OR SERVICE
■
■
■
■
■
■
■
■
■
■
Is the appliance level?
Level the appliance. See the Installation Instructions.
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
Is the proper temperature set?
Double-check the recipe in a reliable cookbook.
Is the proper oven temperature calibration set?
See “Oven Temperature Control” section.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Was the oven preheated?
See “Baking and Roasting” section.
If you need replacement parts
Is the proper bakeware being used?
See “Bakeware” section.
If you need to order replacement parts, we recommend that you
only use FSP® replacement parts. FSP® replacement parts will fit
right and work right because they are made with the same
precision used to build every new WHIRLPOOL® appliance.
To locate FSP® replacement parts in your area, call our Customer
Interaction Center telephone number or your nearest Whirlpool
designated service center.
Are the racks positioned properly?
See “Positioning Racks and Bakeware” section.
Is there proper air circulation around bakeware?
See “Positioning Racks and Bakeware” section.
Is the batter evenly distributed in the pan?
Check to make sure batter is level in the pan.
In the U.S.A.
Is the proper length of time being used?
Adjust cooking time.
Call the Whirlpool Customer Interaction Center
toll free: 1-800-253-1301.
Our consultants provide assistance with:
Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
■
■
■
■
■
Features and specifications on our full line of appliances.
Installation information.
■
■
Are baked items too brown on the bottom?
Move rack to higher position in the oven.
Use and maintenance procedures.
Accessory and repair parts sales.
Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Brand Home Appliances
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Accessories U.S.A.
To order accessories, call the Whirlpool Customer Interaction
Center toll free at 1-800-442-9991 and follow the menu prompts.
Accessories Online.”
Stainless Steel Cleaner & Polish
(stainless steel models)
Order Part #4396095
15
WHIRLPOOL® COOKTOP, BUILT-IN OVEN AND RANGE WARRANTY
FULL ONE-YEAR WARRANTY
For one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool Corporation designated service company.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CLEANTOP® COOKTOP
On ceramic glass ranges and ceramic glass cooktops, in the second through fifth years from the date of purchase, when this
appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will
pay for FSP® replacement parts for the CLEANTOP® ceramic glass cooktop.
Whirlpool Corporation warrants that the ceramic glass cooktop will not discolor, the cooktop pattern will not wear off, the rubber seal
between the ceramic glass cooktop and porcelain edge will not crack, the ceramic glass cooktop will not crack due to thermal shock
and the surface unit elements will not burn out.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace house fuses or
correct house wiring, or to replace owner-accessible light bulbs.
2. Repairs when your appliance is used in other than normal, single-family household use.
3. Pickup and delivery. Your appliance is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God or use of products not
approved by Whirlpool Corporation.
5. Repairs to CLEANTOP®
ceramic glass cooktop or other surfaces if they have not been cared for as recommended in the Use and
Care Guide.
6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
7. Replacement parts or repair labor costs for units operated outside the United States.
8. Any labor costs during the limited warranty period.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
Outside the 50 United States, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another
warranty applies.
If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found
by checking the “Assistance or Service” section or by calling the Whirlpool Customer Interaction Center, 1-800-253-1301 (toll-free),
from anywhere in the U.S.A.
5/00
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your appliance to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label/plate, located on your appliance as shown in the
“Parts and Features” section.
8300610
© 2001 Whirlpool Corporation.
5/01
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
|